The Litter-Robotic 3 is a wonderful gadget for all cat homeowners who need to without end say goodbye to scooping litter. This gadget is designed to allow you to stay in an odorless dwelling, regardless of having cats whereas utilizing much less litter than you’ll usually use. Its magnificence is that it takes care of your entire litter scooping course of by following exact pre-programmed directions that enable correct functioning always.
Nonetheless, like most units, the Litter-Robotic 3 may even encounter just a few points that will impede it from fulfilling its goal. To this finish, it’s important to know the most typical ones forward of time, so you possibly can rapidly resume dwelling in a pleasing dwelling atmosphere with glad cats.
These points are simply fixable, and it’s important to develop into accustomed to the steps wanted to repair them to be ready always. Let’s take a look at a few of the most frequent Litter-Robotic 3 points:
This web site makes use of affiliate hyperlinks that will earn a fee at no extra price. As an Amazon Affiliate, I earn from qualifying purchases.
1. Cat Sensor Troubleshooting
The Cat Sensor is a function that senses when the cat has entered or exited the globe. If the cat sensor breaks down, no different regular operate can happen. Having mentioned this, you will have to observe just a few easy steps to troubleshoot this challenge.
- First, you will have to press the Cycle button, which makes the unit cycle, and return to its Dwelling place – indicated by the stable blue mild.
- Then press the Reset button, enabling you to regulate the cat sensor.
- After this, press the globe’s high simply above the doorway. You are able to do so in a back and forth movement to see if the purple mild engages.
- If it doesn’t, verify how your unit was positioned. To this finish, guarantee nothing is resting in your unit and that it’s not positioned in opposition to a wall. It additionally must be positioned on a stable, degree floor.
What Occurs if the Litter Robotic Globe Jams?
If the Litter-Robotic globe jams, the motor will cease and reverse for just a few seconds. The unit will then attempt to cycle once more thrice. If it can’t cycle after three makes an attempt, the globe will return to the house place, and the management panel will flash yellow and purple or blue and purple lights.
There are some things you are able to do to troubleshoot a jammed Litter-Robotic globe:
1. Flip off the unit and unplug it.
2. Take away the bonnet.
3. Take away the globe.
4. Examine the globe for any particles that may be caught on the surface.
5. Examine the within of the globe for any particles that may be caught on the sifting mechanism.
6. Make it possible for the waste drawer is empty and correctly inserted.
7. Reassemble the unit and plug it again in.
8. Activate the unit.
If the globe remains to be jammed, you possibly can contact Litter-Robotic buyer help for assist.
Listed below are some extra tricks to stop your Litter-Robotic globe from jamming:
Use a high-quality, clumping litter.
Don’t overfill the globe.
Clear the globe and waste drawer commonly.
Examine the sensors and gears for any blockages.
Right here’s methods to troubleshoot your jammed globe:
- To reset the unit and have every thing functioning appropriately once more, you’ll first have to take away the bonnet and put it apart.
- Additionally, you will have to take away the globe, paying consideration to not let it roll. What it’s good to do subsequent is to examine if there’s any liquid accumulation or residue proper the place the globe normally rests, with particular consideration to its high portion from the outside.
- You’ll want to verify for extreme litter and take away it if the case requires it. You will want to make sure there’s a most of 10 kilos of litter or fill it to the road.
- When you’re completed, put the globe and bonnet again in place, making certain all 4 tabs are in place additionally. Lock the black key on the again of the globe into the pocket.
- Plug within the energy provide and switch the unit again on. Your Litter-Robotic will carry out a cycle and return to its Dwelling place with the blue mild on.
3. Fixing a Unfastened Gear on Your Litter-Robotic
Your unit can also have a unfastened or free spinning gear and no globe motion. On this case, it seems that the set screw has come unfastened, and you will have a 3mm hex wrench to repair it.
- First, you will have to unplug the unit, take away the globe, and press on the black gear positioned on the facet. If it strikes, you possibly can proceed the steps.
- You will want to find the shaft hooked up to the gear – that’s the place you can even discover the screw, and if you happen to can see it immediately, you possibly can skip on to utilizing the wrench.
- For those who don’t see it, you possibly can activate the ability and look ahead to the flat facet to rotate into the place that lets you see the set screw. The flat facet of the shaft ought to be dealing with you.
- As soon as aligned, flip off the ability and unplug your Litter-Robotic.
- Utilizing your 3mm hex wrench, tighten the screw by turning it to the suitable.
- When it’s tight sufficient and not strikes, you possibly can place the globe again on the bottom, activate the ability, and press Cycle. Once you see the blue mild once more, you’ll know every thing is again to regular.
4. Bonnet Connections
If the bonnet will not be securely positioned on, the globe received’t rotate, and the yellow mild blinks. Another reason for a defective bonnet connection could also be that the black key on the again of the globe will not be within the slot, and it’s lifting the bonnet.
If, nonetheless, the secret’s in place and the bonnet appropriately assembled, but the yellow mild is flashing nonetheless, chances are you’ll have to:
- Disconnect the bonnet.
- Flex the 2 bonnet tabs outwardly.
- Reattach the bonnet – you’ll realize it’s securely in place while you really feel a snap and listen to a ‘click on.’
- Whereas the bonnet is eliminated, you can even use a moist fabric to scrub the 2 metallic sensors on the left facet of the bonnet.
- Examine the nightlight connection if you happen to’re nonetheless encountering the difficulty. There are wires on the underside of the bonnet and in a micro connector. This, in flip, plugs into the circuit board contained in the evening mild housing. All it’s good to do is push this micro connector into the circuit board to make sure correct connection.
- The fin of the globe can also catch a few of the bonnet wires, resulting in the pause of the rotation.
- It’s additionally really useful to verify if there are any unfastened or pulled wires and safe them by taping them flat in opposition to the bonnet.
5. Blue Gentle Blinking
Concerning points along with your Litter-Robotic 3, you might also see the blue mild blinking. Earlier than troubleshooting, it’s advisable to:
- Unplug your energy provide after which look forward to 10 seconds.
- Plug the unit again in and permit it to finish its cleansing cycle.
- If the sunshine is stable blue, every thing has reverted to regular.
If the sunshine remains to be blinking, you will have to troubleshoot. Nonetheless, earlier than you proceed, it’s good to make sure the waste drawer is empty and has a clear liner.
Blue blinking mild: The bag isn’t totally inserted within the drawer
A blue blinking mild, however the bag is inserted appropriately: The DFI lens is normally soiled; wipe them with a fabric.
To begin with, you will have to verify your DFI lenses for any obstructions:
- Flip off your Litter-Robotic and unplug from the ability base, after which you’ll be able to take away the bonnet and globe.
- Search for extra litter and clear accordingly the place the globe normally rests.
- Search for the inexperienced circuit board throughout the waste port of the bottom.
- Use a Q-tip to scrub the sensor eye gently.
- Exchange the globe and bonnet whereas making certain the black key from the again of the globe is safe in its slot.
- Plug your unit again in, energy it on, and press Cycle. After finishing the cleansing cycle, the unit ought to return to its Dwelling place with a stable blue mild on.
If the difficulty persists, you will have to troubleshoot additional:
- Take away the waste drawer and press the Cycle button.
- Press Reset twice to abort the cycle and return to the Dwelling place.
- Whereas eradicating the waste drawer, be sure there isn’t something within the drawer that could be blocking the sensor – by which case you’ll see a stable blue mild.
- If the drawer is evident, it’s time to name Buyer Service for the reason that base wants repairing.
6. All Three Lights Blinking
You’ll find that along with your Litter-Robotic, chances are you’ll encounter one other technical challenge that manifests itself via all three lights blinking. (Learn our entire submit devoted to this.) Now, there will be three totally different the reason why this can be occurring, so let’s check out every one in all them:
- There’s extra weight within the unit. Examine the litter degree and guarantee it’s not above the Fill line. For those who take some litter from the globe, hit the Restart button afterward. One other approach to take away extra weight is to empty the waste drawer, particularly if it’s getting near full.
- Examine your energy provide. First, guarantee there is no such thing as a injury to the ability wire and verify that your adapter meets the specs: 15VDC regulated adapter 400mA to 1000mA. For those who’ve plugged your unit into an extension wire, strive switching to a wall socket and see if there’s any distinction.
- Examine the inner protect or black key in the back of the globe. As a notice, all Litter-Robots bought after February twenty first, 2018, won’t have an inside protect however, as an alternative, the black key. When not set appropriately, both of them may cause disruptions to the biking course of. When the unit is within the Dwelling place, the protect ought to be within the high left nook, and the important thing ought to be positioned appropriately within the groove within the base.
- Examine the bonnet. It might must be positioned appropriately. Make sure that every of the 4 tabs is appropriately secured, two curved within the again and two on the perimeters. It is best to hear a ‘click on’ when that occurs.
- For those who discover the globe lifting through the cycle course of, it could be as a result of it’s encountering resistance. This implies there will likely be friction between the plastic of the globe and the bottom, inflicting the magnets within the globe to skip the place sensor, additional resulting in the three blinking lights. A easy answer is to use furnishings polish to the globe’s tracks. Every time you make adjustments to the unit, bear in mind to press Reset.
[adthrive-in-post-video-player video-id=”FHXne83E” upload-date=”2022-11-01T04:40:45.000Z” name=”Litter Robot Open Air Self Cleaning Litter Box Review – Should You Get It.mp4″ description=”null” player-type=”default” override-embed=”default”]
7. The Contemporary Restart
If no different troubleshooting technique works, it’s finest to strive the Contemporary Restart approach, as instructed by the workforce at Litter-Robotic. This could allow you to determine and additional talk the difficulty to the Buyer Service workforce. Right here’s what it’s good to do:
- First, press the Energy button and switch the Litter-Robotic off, then unplug the ability provide from the again of the bottom.
- Disassemble the bonnet and globe by miserable the facet tabs, tilting the bonnet backward, then lifting it up and setting it apart.
- Whereas within the Dwelling place, additionally fastidiously take away the globe.
- Guarantee the bottom is on agency, degree floor and never pushed in opposition to the wall. The Litter-Robotic should not be leaning on something.
- Empty the waste drawer regardless that it will not be full.
- Reassemble the Globe again within the Dwelling place. For those who sense its weight could also be imbalanced, gaze into the litter pocket via the display screen. Examine for any caught litter, which can throw off the unit throughout biking. Clear the Globe accordingly.
- When you align it on monitor, make sure the litter degree contained in the globe is at or beneath the raised Fill line.
- Reassemble the bonnet by aligning the rear tabs within the base. Tilt the bonnet ahead and snap the tabs into place, making certain they’re secured.
- Additionally, you will want to make sure the black key in the back of the bottom is correctly secured in its pocket.
- Plug the ability provide again into the bottom and switch the unit on.
- Your Litter-Robotic ought to now carry out a cleansing cycle. It is going to rotate to the dump place, previous the Dwelling place to degree the litter inside, after which again to the Dwelling place once more, with a stable blue mild. It’s vital to notice that the Cat Sensor is mechanically reset on the finish of every cycle carried out.
- To manually activate the Cat Sensor, press the globe simply above the doorway utilizing a forward-backward movement after which launch. This could activate the Cat Sensor. You will notice the blue mild going off and the purple one occurring as an alternative – as a simulation of a cat getting into and exiting the unit. Enable the unit the wait time you’ve set it to, regardless if it’s 3, 7, or quarter-hour, and the clear cycle to complete. If the globe returns to the Dwelling place with a stable blue mild, your Litter-Robotic is functioning appropriately.
8. Litter-Robotic Turning the Mistaken Method
One other challenge along with your Litter-Robotic 3 could also be that it will possibly flip the unsuitable manner from what it’s imagined to. Suppose you’re confronted along with your Litter-Robotic turning the unsuitable manner. In that case, it’s normally on account of one of many following two causes:
- The difficulty could also be attributable to malfunctioning the circuit board, which can want changing. It’s really useful that you just discuss to the Litter-Robotic help workforce about this.
- The difficulty could also be attributable to the harness/magnetic sensor. It might be slowly giving out, so as soon as once more, you will have to speak to the Litter-Robotic help workforce and see if it’s good to exchange it.
9. Litter-Robotic Corridor Impact Sensor
The Corridor Impact Sensor is an integral a part of the Litter-Robotic, and the core know-how makes it such an clever machine.
- The Corridor Impact Sensor is a part of the Wiring Harness and is barely bought along with it.
- We’ve talked earlier than concerning the three lights blinking. Suppose you’ve checked the voltage of the ability provide and the set screw on the motor, and the difficulty persists. In that case, it comes all the way down to the Corridor Impact Sensor, which can want changing.
If you end up in want of changing the Wiring Harness system, relaxation assured it’s a simple course of so long as you observe these steps:
1. Opening the Management Panel
- Make it possible for, initially, you narrow off all energy out of your Litter-Robotic by unplugging the machine.
- Take away the Bonnet, Globe, and Waste Drawer.
- On the highest of the bottom, known as the bezel, you will see that 5 screws – unscrew them to take away the highest.
2. Look For the Circuit Board and Sensors
- Raise the bezel by utilizing needle-nose pliers.
- You’ll now see the Corridor Impact Sensors, the circuit board, and the motor.
- You’ll discover 3 connectors on the motherboard – gently unplug them.
- The motor may even have 2 connectors – unplug them after which take away the motor.
- It’s possible you’ll discover tape holding the Circuit Board and Keypad in place – take away it with out second ideas.
- Discover and take away the wire locker.
3. Opening the Base
- The following step is to show the bottom the other way up whereas making certain the management panel has no unfastened elements inside.
- You’ll discover 9 screws right here – take away them.
4. Eradicating the Whole Harness
Earlier than you undergo this course of, be sure to take a psychological notice of how the wiring on the Litter-Robotic was made. Higher but, take a photograph of your entire electrical association so that you’ll have one thing to show to while you assemble again the machine.
- Use the pliers from earlier than and punctiliously take away the Energy Jack.
- The blue and black wires symbolize the Cat Sensor’s connector – unplug them.
- The purple and black wires symbolize the Bonnet’s wires – unplug them.
- The purple and black wires symbolize the Battery wires – gently take away them.
5. Putting in the New Wiring Harness
- Plug again within the blue and black wires representing the Cat Sensors.
- Move the purple and black wires, representing the battery wires within the small gap.
- Plug again within the white and black wires representing the Energy Jack Connector.
- Plug again within the purple and black wires representing the Bonnet’s connectors.
- Move the Corridor Impact Sensor via the Management Panel gap.
6. Putting in Again the Management Panel
- Make sure that all wires go beneath the Motor.
- Clip again the Wire Locker.
- Set up the motor and take note of the wiring: purple with inexperienced and white with brown.
- Set up the plastic piece with the Corridor Impact Sensor in place.
- Safe the Corridor Impact Sensor by including a chunk of tape.
- Plug again these 3 preliminary connectors on the Circuit Board.
7. Closing the Unit Again
- Clip again the principle board on the plastic panel.
- Screw again all of the preliminary 5 screws whereas making certain all of the wires are plugged in securely.
- Screw again the 9 screws on the again of the bottom from earlier on.
8. Plug It Again It and Give It a Run
- When you’ve reassembled the unit, be sure to additionally set up the Globe.
- Plug the ability provide again in.
- If it doesn’t energy up mechanically, press the Energy Button.
- Let the unit cycle and observe its program.
10. Litter-Robotic Received’t Cycle Routinely
Suppose you discover your Litter-Robotic received’t cycle mechanically, and the yellow mild received’t flip off. In that case, it’s most definitely as a result of it entered Sleep Mode. This mode has been created so that you can have some peace and quiet for eight hours, particularly if the Litter-Robotic is positioned someplace the place, at occasions, you require no disturbance.
When you set the Sleep Mode on, it won’t cycle mechanically for 8 hours straight. Nonetheless, as soon as these 8 hours are completed, a Clear Cycle will start. Press and maintain the Cycle button to exit the Sleep Mode till the yellow mild turns off.
11. Litter-Robotic Received’t Cycle Routinely, Doesn’t Detect the Cat
The Litter-Robotic Cat Sensor is created for the Litter-Robotic to know when the cat enters and exits the unit. Each time the unit is turned on, the Cat Sensor measures the burden of the unit and detects if there are any adjustments to it.
[adthrive-in-post-video-player video-id=”bftD7Xue” upload-date=”2022-11-01T04:46:35.000Z” name=”Litter Robot 3 – LR3 – Weight Sensor Timer” description=”This Whisker Litter Robot 3 video addresses the weight sensor timer.” player-type=”default” override-embed=”default”]
Urgent the Reset Button each time you modify the burden of the Litter-Robotic will allow it to know that one thing has modified. It’s really useful that you just press the Reset Button in any of those instances:
- You’ve emptied the Waste Drawer;
- You’ve cleaned the unit;
- You’ve moved the Litter-Robotic.
When you press the Reset Button, the blue mild will flash, and the Cat Sensor will likely be reset and reactivated.
The Cat Sensor’s regular functioning could also be affected everytime you:
- Place the Litter-Robotic on an uneven floor, in opposition to the wall or on the carpet;
- You haven’t crammed the Litter-Robotic with sufficient litter to fulfill the raised Fill Line;
- Your cat weighs lower than 5 lbs;
When the Litter-Robotic doesn’t detect your cat, carry out these fast checks:
- Take a look at the show in your unit. If each the blue and yellow lights are on, the unit is in Sleep Mode.
- For those who discover a grimy litter field and the sunshine doesn’t change from blue to purple when the cat is inside, then the Cat Sensor didn’t appropriately detect your cat. Check this by urgent the Cycle button, so the unit can carry out a Clear Cycle. Afterward, it ought to merely return to the Dwelling place with a stable blue mild on, indicating that every thing is operating usually. You may then press the Reset button, which can make the blue mild blink and which verify the Cat Sensor has been reset.
- You may then take a look at the Cat Sensor by urgent again and away on high of the entry unit in direction of the again of the unit. The blue mild ought to flip purple as if the unit registered your cat is inside. If it does, it’s an amazing signal. Press the Reset button, and the unit will return to its blue standby mild. If the sunshine didn’t flip purple, your Cat Sensor didn’t really feel the stress you utilized, so that you’ll have to carry out a Exhausting Reset.
- To carry out a Exhausting Reset, make sure the globe is within the Dwelling place, and there’s a stable blue mild on. Take away the ability provide from the again and wait 10 seconds, after which you’ll be able to plug it again in. Now you can enable the unit to finish a Clear Cycle, then press and maintain the Cycle button for five seconds. Each the blue and yellow lights will activate – now press and maintain the Cycle button for five seconds. It will flip the yellow mild off whereas the blue mild stays on. Now you can activate the Cat Sensor by urgent down and away on the unit entryway in direction of the again. The purple mild ought to come on now – if it does, it’s an amazing signal. Enable the unit to complete its Clear Cycle. As soon as within the Dwelling place once more, the unit will likely be reset. If the purple mild didn’t activate, it’s really useful that you just contact Buyer Service.
12. Litter-Robotic Will get ‘Caught.’
It could possibly additionally occur sometimes when your Litter-Robotic will get ‘caught.’ In case this occurs, one of many following eventualities could apply:
- There could also be an excessive amount of litter within the Globe;
- The kind/model of litter is heavier than the common litter. On this case, you possibly can put rather less than you’ll usually do with common litter – fill in slightly below the Fill Line. In case your litter is common, put in simply sufficient so it’s beneath the raised Fill line or reaching this degree.
13. Litter-Robotic Is Dumping Clear Litter
In case this occurs, you must know that most definitely there’s an excessive amount of litter within the globe. So scoop some out, and while you fill within the unit the subsequent time, make sure the litter degree is at or beneath the raised Fill Line.
14. The Waste Contained in the Litter-Robotic Sticks
For those who observe the waste sticking, you possibly can regulate the Litter-Robotic Wait Time setting to accommodate your litter – you are able to do so by lowering or rising it.
The Wait Time is the elapsed time between the second your cat exits the globe and the unit begins a Clear Cycle. It may be set for 3, 7, or quarter-hour, though the default Wait Time is 7 minutes.
Once you cut back the Wait Time:
- You’ll have the prospect to cut back disagreeable odors;
- Or cut back the time that litter is obtainable to different pets as effectively;
- You might also cut back cleansing effectiveness if the litter lacks sufficient time to clump.
Then again, you can even prolong the Wait Time while you’re utilizing lower-quality litter that wants extra time to clump up;
To arrange the Wait Time:
- Press and maintain the Empty button for about 5 seconds. One of many lights will begin flashing, indicating the present setting for the Wait Time.
- Use the Reset Button to change to the next setting: blue for 3 minutes, yellow for 7 minutes, and purple for quarter-hour.
- Press and maintain the Empty button to save lots of the setting you chose. The blue mild will blink to verify your alternative, then return to its stable standby place.
All in all, these are the most typical points you possibly can encounter when proudly owning the Litter-Robotic 3. In fact, they could or could not happen. Nonetheless, by realizing these steps talked about above, you’ll be capable to efficiently get out of any disagreeable scenario that will come up.
Hello, I’m Jenny Dean, creator of Floppycats! Ever since my Aunt bought the primary Ragdoll cat in our household, I’ve beloved the breed. Impressed by my childhood Ragdoll cat, Rags, I created Floppycats to attach, share and encourage different Ragdoll cat lovers all over the world,
